Zinc Coating Thickness Requirements: ASTM A vs. F Dimension. ASTM A ASTM F Avg. Coating. Thickness of. Specimens. Tested. 23 Feb ASTM F covers the requirements for hot-dip zinc coating applied to carbon steel and alloy steel bolts, screws, washers, nuts, and special. ASTM F – Download as PDF File .pdf), Text File .txt) or read online.
|Published (Last):||25 December 2011|
|PDF File Size:||8.43 Mb|
|ePub File Size:||6.23 Mb|
|Price:||Free* [*Free Regsitration Required]|
This specification covers the requirements for hot-dip zinc coating applied asstm carbon steel and alloy steel bolts, screws, washers, nuts, and special threaded fasteners applied by the hot-dip coating astm f2329. Adhesion testing is astm f2329 typically performed when galvanizing astm f2329 the requirements of A unless there is evidence of an adhesion concern, but F requires adhesion testing stout astm f2329 test to be performed for the number astm f2329 articles listed in Table 1, and for every batch lot.
The following tests shall be made to ensure that the zinc coating is being furnished in accordance with this specification: For long pieces anchor rods or articles greater than five feet aztm lengthcoating thickness measurements must be taken on each end and in the middle of the article.
The major differences v2329 the two specifications, described below, include topics related to sampling protocol, coating thickness, inspection, embrittlement, and documentation.
This method is similar to astm f2329 inspection of coating thickness on multi-specimen articles galvanized per ATSM A It is important to note the acceptance criterion in all cases is zero defects. The test methods for appearance and smoothness under F shall be conducted for every batch lot by visual inspection in accordance with methods provided in A It also astm f2329 for minor coating repairs.
Best practice is to note the bath temperature when galvanizing steel to F, although only the average bath temperature is zstm. The amount of additional documentation beyond ASTM A requirements will vary astm f2329 on a number of optional requirements the customer can specify under F Table 2 of F lists average coating thickness requirements for production lots, batch lots, and individual specimens.
See excerpt astm f2329 Table 1 below.
ASTM F vs. ASTM A | American Galvanizer’s Association
Astm f2329 is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations f329 to use. Suppliers shall furnish certified test results from which the shipping lots originated. The acceptance number in all cases is zero astm f2329.
However, if a purchaser also requires the astm f2329 to inspect dimensional requirements astm f2329 parts upon delivery, they must provide the galvanizer with the necessary tools and inspection gauges. Coating Thickness Table 2 of F lists average coating thickness requirements for production lots, batch lots, and individual specimens.
ASTM F2329 vs. ASTM A153
The differences in the types of lots entail different sampling plans, which specify the number of test articles for performing various test methods during inspection of the finished product. These instances astm f2329 include when steel has been severely work astm f2329 or when the galvanizing bath temperature exceeds the stress relief or tempering temperatures of the fasteners. Otherwise, astm f2329 third party will be required to apply the lubricant at an additional cost. Furthermore, there are two types of production lots: The zinc used for the coating shall conform to the chemical composition required.
Therefore, it must be clarified whether the plant has the asm to lubricate hardware after hot-dip galvanizing. Each bolt specification may list additional methods to prevent astm f2329 embrittlement as well as place additional requirements on embrittlement testing which should be researched separately. Astm f2329 Coating Thickness Requirements: ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.
The coating thickness requirements of A Table 1 meet or exceed those of F Table 2 except f2239 Galvanizing fasteners in accordance with A, will usually astm f2329 or exceed the requirements of F, because F defers to A in many sections.
ASTM F – Portland Bolt
For example, a lot size of articles under the detection process requires testing of 11 astm f2329 c2329 coating thickness, 11 samples for visual appearance, and 3 samples for adhesion. Quenching According to F Paragraph 5. The values stated in each system may not be exact equivalents; therefore, astm f2329 system shall be used independently of the other.
The type of production lot process will determine which column should be referenced astm f2329 the sample size of each astm f2329 criteria, as summarized in the table below, or per the F Sampling Plan Flow Chart.
The temperatures used in the hot-dip galvanizing process typically do not appreciably alter the mechanical properties of steel, but there are astm f2329 instances when there are potential concerns.
Work Item s – proposed revisions of this standard.
Authored by Alana Hochstein. Link to Active This link astm f2329 always route to the current Active version of the standard.