DIGITAL COMPASS WITH ALTIMETER. Instruction Manual. 1. Introduction. Features: Altimeter (m, feet). Digital compass. Barometric pressure (hPa, inHg. Manual gearbox. MAN/TEN: Manual tensioner .. Caja de cambios manual CIELO. 8V. – 97 A -PAS. +V/BLT. AVX10 +P-V/BLT. 5PK Manual de utilizare statie de calcat Bosch TDS Vezi intreaga gama de fiare de calcat.

Author: Akinojinn Akirg
Country: Guinea-Bissau
Language: English (Spanish)
Genre: Art
Published (Last): 17 March 2004
Pages: 215
PDF File Size: 5.2 Mb
ePub File Size: 1.59 Mb
ISBN: 793-1-23469-459-1
Downloads: 59989
Price: Free* [*Free Regsitration Required]
Uploader: Zulkihn

Manual de utilizare statie de calcat Bosch TDS1625

Remove the camshaft followers using the valve spring compressor KMA. Position the fan, the collars, and the pulley on the rotor shaft and secure with the nut. This 28 mm setting is also an adequate setting for controlled idle on a tehnifa. Inspect all of the crankshaft bearing clearances using a commercially available plastic gauging ductile plastic threads. AB Installation Procedure 1.

Inspect the EGR valve, passages and pipe for a restriction or damage and repair as necessary.

daewoo cielo green used – Search for your used car on the parking

Check if any additional DTCs are set. Use the angular torque gauge KMB to tighten the flywheel bolts another 30 de- grees plus 15 degrees. Tighten Tighten the camshaft gear coelo to ttehnica N m 33 lb-ft. Inspect the engine block cylinder bore for wear, run- out, ridging and taper using a bore gauge. If the catalyst is functioning properly, the HO2S 2 sig- q F. DTC s can be cleared by using the scan tool.

Related Articles  K9F2G08U0C EPUB DOWNLOAD

Push the pinion back as far as possible to take up any movement, and check the clearance with a feel- er gauge. Connect the sensor electrical connector. Page 30 and the fuse F The idle learn procedure is tested.

Make ciwlo that the clip is parallel to the fuel injector harness connector. Fill the coolant system. Page 88 10 N m 89 lb-in. Install the camshaft gear.


Tighten the idle air control valve retaining bolts to 3 NSm 27 lb-in. Go to Step 10 Go to Step 11 Does the test light illuminate? Take extreme care to prevent any scratches, nicks, or damage to the camshaft.

Go to Step 10 Go to Step 8 Is the repair complete? Install the needle bearing. Total Misfire Current Counter Indicates the total number of misfires that have been de- tected in all the cylinders after engine cycles. Connect the negative and the positive battery cidlo.

Check the engine control module ECM electrical connector for poor — connections and repair as necessary. Crank test each cylinder with four to five compression.

Page This 28 mm setting is also an adequate setting for controlled idle on a restart. Page M5 for an open or short. Inspect the ECM ground connections. Page Is the problem found? Install the timing belt automatic tensioner bolt.


Page AE Do not start the en- gine. Connect the IAT sensor connector. Position the armature assembly into the field frame. Repair or replace any faulty components. D Engine cartee time is greater than 60 seconds. Repair the open wire between the cooling fan relay A connector terminal 85 and the ECM — — connector terminal K Remove the fuel pressure regulator by turning it back and cafte and then pulling it out.

Manual de utilizare router D-link DIR | Manuale de utilizare

Connect a test light between the fuel pump relay connector terminal 86 and ground. Connect the negative battery cable. Install the oil pan within 5 minutes after ap- plying liquid gasket to the oil pan.

Does the scan tool indicate that this diagnostic ran Go to Step 11 Go to Step 3 and passed? The engine coolant temperature is greater than 60 q C ly.