CISCO MDS 9124 CONFIGURATION GUIDE PDF

Example Cisco MDS Switch Default Port License Configuration. switch# show port-license Available port activation licenses are 0. Cisco MDS Family Quick Configuration Guide. OL Using the Switch Setup Utility Verifying the Module Status CHAPTER. 3. Configuring. Note If a Cisco MDS or switch is used as a core switch, only a nontrunking F PortChannel is supported. Trunking is not supported on.

Author: Kajijind Tygojind
Country: Guinea-Bissau
Language: English (Spanish)
Genre: Video
Published (Last): 1 December 2010
Pages: 473
PDF File Size: 2.4 Mb
ePub File Size: 6.95 Mb
ISBN: 309-9-36362-763-9
Downloads: 57460
Price: Free* [*Free Regsitration Required]
Uploader: Kajibei

Unofficial Cisco MDS Release 3.x CLI Config Guide Errata

This is not correct. This should be made more clear. The opinions expressed in this blog are entirely my own and should not be taken as the opinion of my employer. Should say Step 1 Enable the mgmt 0 interface. You basically give the same settings for the IBM blade switch but this is a 24 port not a 20 port. If you enabled the autoreconfigure option on both switches before connecting the fabric, a disruptive reconfiguration RCF will occur.

I think what is meant here is: This page incorrect states that fcns reject-duplicate-pwwn is disabled by default.

Have a few different people read that and I think you will see where I am coming from. You must be logged in to post a comment.

The autoreconfigure option takes immediate effect at runtime. If you do not need explicit LUN access control, using the proxy initiator mode simplifies the configuration.

This situation can guidee several configuration tasks for each iSCSI host. Page Figure shows incorrect ip default-gateway Page States in one bullet: Although it can be configured it has no effect.

Related Articles  CETONURIA PDF

Page shows with 8 base ports 8 licensed for growth.

Unofficial Cisco MDS Release 3.x CLI Config Guide Errata – Maximum Entropy

Page Information is repeated twice on the same page: I am not sure. IP routing does not have to be enabled, unless there is cnfiguration specific topology where IP routing is necessary. Page Document states: A disruptive reconfiguration may affect data traffic.

This page incorrectly states that you can disable password verification with aaa authentication login none command. You can nondisruptively reconfigure the fcdomain by changing the configured domains on the overlapping links and getting rid of the domain overlap.

There is no information contained in the example given that shows the configuration or enabling of FCIP interfaces. On the same page I find this block of text very vague and confusing: I am not sure if this is cissco. This however would be very nice to have in the documentation for IPS network simulator, an example showing complete configuration of Gigabit Ethernet interfaces and FCIP tunnels to go along with the Network Simulator.

You cannot mix ingress and egress interfaces in the same SPAN session. Then states two bullets later: Obviously there was a part of this paragraph that cidco chopped off msd. Proudly powered by WordPress. The default authentication port is About System Message Logging properly configured system message logging server.

Certainly there is either a mistake in the wording or the example. FCIP uses different ports. It is worded as if it is a requirement but it is vuide fact not. Caution The span drop-threshold can be connfiguration only if no span sessions are currently active on the switch. This is not correct as this does not work. This blog is mostly about my pursuits in Data Science. I am not sure that the statement in bold is correct. Previous blog entries also dealt with storage, compute, virtualization and professional services.

Related Articles  SINDROME DE GUILLAIN BARRE PDF

Leave a Reply Cancel reply You must be logged in to post a comment.

If you assign port number for physical portshow can you assign for ports ? This is not true. Should be 8 base ports, which can goto 8 or 16 additional ports. These pages talk about an active mode of fcanalyzer. Configurayion as in changing of domains is always disruptive. If a domain is currently isolated due to domain overlap, and you later enable the autoreconfigure option on both switches, the fabric continues to be isolated.

You do not need to restart the fcdomain. Cisco Documentation team has internally re-written this as: In this case, using the proxy initiator mode simplifies the configuration.

From time to time I will blog about other things of interest. The way its written sounds like if you have a large scale deployment where you need explicit LUN access control you can use proxy-initiator, but its really the opposite.